Baker Drill Pipe Float Valve

Kami jual dan Stok Baker Drill Pipe Float Valve Jakarta Indonesia.

Baker Drill Pipe Float Valve Baker SPD is the original manufacturer of Baker Drill Pipe Float Valves. Baker Drill Pipe Float Valves have become an industry standard with their superior engineering, quality, construction, and dependability in service and are committed to continuous improvement. Baker SPD manufactures a complete line of Float Valves, Repair Kits, and Puller Assemblies to accommodate a wide range of drilling situations and operating conditions, including H2S and Steam Service. These Drill Pipe Float Valves provide added blowout protection at the bottom of the drillstring, prevent flowback when joints are added, and keep cuttings out of the drillpipe to prevent bit plugging while making connections. Note: It is recommended that if multiple Drill Pipe Float Valves are run in the same string, they be separated. However the Model GS may be stacked. Baker SPD Drill Pipe Float Valves have been designed, manufactured, tested, and certified in accordance with accepted engineering, manufacturing, and quality assurance standards including, but not limited to, the following documents or publications. Quality Construction American Iron and Steel Institute ( AISI) American National Standards Institute ( ANSI) American Society for Testing and Materials ( ASTM) American Society for Metals ( ASM) American Welding Society ( AWS) Rubber Manufacturer’ s Association ( RMA) Society of Automotive Engineers ( SAE) Rated Operating Pressure Model F Drill Pipe Float Valves rated 7, 500 WP Model G & GS Drill Pipe Float Valves rated 7, 500 WP Cages Cage construction of the various Models F and G includes ductile iron and low alloy steel on the 6F size only. Hardness levels of these are at or below 22 Rockwell C to resist hydrogen sulfide stress cracking when used for H2S applications. The Model GS cage is made from low alloy steel. There is an option for low alloy steel cage in some Model F sizes. Stainless steel available upon request. Springs Models F and G utilize high alloy springs for all applications. Seal and Shock Absorber Elastomers Application Material Temperature Standard Nitrile ( BUNA) 100° C [ 212° F] Hi-Temp Viton 204° C [ 400° F] H2S HSN/ HNBR 149° C [ 300° F] Hi-Temp H2S L' Garde 232° C [ 450° F] Geothermal L' Garde 232° C [ 450° F] Steam L' Garde 232° C [ 450° F] Hi-Temp Over 450° F KALREZ ( FFKM) 327° C [ 620° F] H2S/ Steam/ Geothermal Float Valves are manufactured with alloy steel integral, cages & plungers to produce the most reliable float valve on the market today. All Flappers are investment cast and then case hardened for wear resistance. Elastomers available are Nitrile Butadiene ( NBR / Buna N) , Hydrogen Nitrile Butadiene ( HNBR) , and Viton® ( Fluoroelastomer / FKM) . Inconel® or stainless steel springs come standard on all our valves and are significantly more resistant to corrosion when compared to standard service springs provided by most other manufacturers. Product Model F The Model F is a plunger-type float valve that provides a positive instantaneous shut off, providing constant fluid control while drilling. Model FA The Model FA Pressure-Monitoring plunger-type float valve has a special port running through the plunger of the float valve. This valve is used when monitoring the bit head for gas pressure and allowing differential pressure measuring when required. Model FC The Model FC Automatic-Fill plunger-type float valve incorporates a unique key assembly and slotted valve stem to hold the plunger open during run in of the drill pipe and allows the pipe to fill from the bottom, saving time, reducing mess, and avoiding hazards. Model G The Model G is a flapper-type float valve that, when opened, offers an unobstructed bore through the float valve. Model GA The Model GA Pressure-Monitoring flapper-type float valve is indistinguishable from the Model G with the exception of a tungsten-carbide insert in the flapper valve. Model GC The Model GC Automatic-Fill flapper-type float valve incorporates a unique self-releasing key assembly that holds the flapper partially open during run in, allowing the pipe to fill from the bottom. Model GCA The Model GCA Automatic-Fill/ Pressure-Monitoring flapper-type float valve includes all the advantages of the Models G, GC, and GA. Model " F" Plunger Type Valve The Model F plunger type valve offers positive and instant shut-off. In normal drilling operations the Model F offers economy and durability. The piston stops flow-back when making connections and keeps cuttings out of the drill string. Model " FA" Ported Plunger Type Valve The Model FA offers all the standard features of the Model F float valve with the added feature of a ported piston, which allows a fluid path through the center of the valve. This feature allows for an automatic partial filling of the drill pipe during run in. Model " FBP" Integral Baffle Plate Valve The Model FBP also offers all the standard features of the Model F float valve with the added feature of an integral baffle plate at the top of the float valve which is both heavy duty and shatterproof. For operations where a baffle plate is always used for instrumentation or fluid control, the integral baffle plate configuration offers an economical option. The Model FBP is available in 3 sizes; 31/ 2 IF, 4R and 5F-6R. Model " G" Full Flow Flapper Type Valve The Model G flapper type valve features an investment cast flapper that is quick opening, allowing for full flow through the valve. The Model G is designed for highly abrasive drilling fluids. Model " GA" Flapper - Full Flow Ported with Carbide Orifice The Model GA is identical to the Model G except for a carbide orifice that makes the flapper ported. The Model GA flapper allows for differential pressure readings at the surface. Model " GC" Flapper - Full Flow Automatic Fill The Model GC is identical to the Model G but adds an automatic fill feature when going in the hole. The Model GC helps prevent pressure surges that could cause formation breakdown. Model " GCA" Full Flow Flapper with Carbide Orifice Valve The Model GCA is identical to the Model GA but adds the automatic fill feature. Model “ F” Plunger Type valve Product Family No’ s. H48013 ( Standard Style) and H48043 ( Heavy Duty Alloy Style) This valve offers positive and instant shut-off. In normal drilling operations this model offers economy and durability. The piston type stops flow-back when making connections and keeps cuttings out of the drill string. Part Numbers for Valves: 1R 480131200, 1F-2R 480131422, 2F-3R 480132432, 3F 480133400, 3-1/ 2F IF 480133600, 4R 480134200, 4F 480134400, 5R 480135200, 5F-6R 480135462, 6F 480136400. Rubber & Metal Repair kits: 01612200, 016012300, 016012400, 016012500, 016012600, 016012700, 016012800, 016012900, 016013000, 0160113100, 015929800, 016011300, 016011400, 01611500, 01611600, 016011700, 016011800, 016011900, 016012000, 016012100. Model “ FA” - ( Plunger Type Valve) Product Family No: H48012 The Model FA offers all the standard features of the Model F Float Valve with the added feature of a port which allows a fluid path through the center of the valve. This feature allows for an automatic partial filling of the drill pipe during run in. This valve is used when monitoring the bit head for gas pressure and/ or gas pockets, allowing measurement of differential pressure when required. The Model FA is available in all sizes. The Model FI also offers all the standard features of the Model F Float Valve with the added feature of an integralbaffle plate at the top of the float valve. For operations where a baffle plate is always used for instrumentationor fluid control the integral baffle plate configuration offers and economical option. The Model FI is only available in sizes 4R and 5F-6R. Part Numbers for Valves: 2F-3R 480122432, 3F 480123400, 3 1/ 2 IF 480123600, 4R 480124200, 5R-6R 480125462 Rubber & Metal Repair Kits: 016012405, 016012505, 016012605, 016012705, 016013005, 016011405, 016011505, 016011705, 016012005 Model “ G” Flapper – Full Flow Product Family No. H48015 The Model G “ Flapper Type” Full Open Valve incorporates a specially designed flapper which opens quickly and fully to provide a completely unrestricted bore through the valve. The Model G is especially good for use with highly abrasive fluids. When circulation stops, the flapper closes instantly to prevent cuttings from entering the drill string and plugging the bit. The valve opens when the first joint is raised out of the hole assuring the first joints drain and are not pulled wet. This saves mud and avoids safety hazards and down time. The flapper-type valve complements primary blowout prevention equipment to provide complete internal pressure control. Part Numbers for Valves: 1F-2R 480151422, 2F-3R 480152432, 3F 480153400, 3 1/ 2 IF 480153600, 4R 480154200, 4F 480154400, 5R 48015520, 5F-6R 480155462 Rubber & Metal Repair Kits: 051988300, 016013800, 016013900, 051982000, 016014000, 016014100, 016014200, 016014300, 051988400, 016013200, 016013300, 052070200, 016013400, 016013500, 016013600, 016013700 Model “ GA” Flapper - Full Flow with Carbide orifice Identical to the “ G” except for a carbide orifice in the flapper. Allows differential pressure readings at surface. Model “ GC” Flapper – Full Flow Automatic Fill Identical to the “ G” but adds an automatic fill feature when going in the hole. Helps prevent pressure surges that could cause formation breakdown. Model “ GCA” Flapper – Full Flow with Carbide orifice Identical to the “ GA” but adds the automatic fill feature